WaHa FAQ

Atmospheric water generation FAQ: how the WaHa Vaporator® makes pure water and inexpensive dry air

WaHa Inc. makes the WaHa Vaporator®, a machine that makes pure water and inexpensive dry air from the air. This page answers the questions customers, partners and investors ask most about how the WaHa Vaporator® works, where it works, and how to buy one.

The basics

What is atmospheric water generation?

Atmospheric water generation (AWG), also called atmospheric water harvesting, means making liquid water from the water that is already in the air. Air always carries some water as an invisible gas, called water vapor. An AWG machine pulls that vapor out of the air and turns it into water you can collect.

How is the WaHa Vaporator® different from other water-from-air machines?

Many water-from-air machines work like a refrigerator. A compressor cools the air until drops of water form, the way water beads on a cold glass. That works best in warm, humid air, like Miami, Houston, Singapore, or Mumbai.

It stops working when the air is only a little cool. Below about 15°C (59°F), the cold coils frost over, the way a freezer does, and the machine has to stop and defrost them. That is not very cold. In many places in the U.S., even in summer, evenings drop below 15°C (59°F). In Southern California, it happens often. These machines also slow down or stop where the air is dry, like Phoenix or Las Vegas in early summer, where it is hot but your lips and skin dry out fast. Very hot weather, above about 43°C (109°F), stops them too.

Some other machines use a drying material, as we do. What sets the WaHa Vaporator® apart is our sealed regeneration engine. "Regeneration" means drying out the material again so it can catch more water. Our engine is sealed: the water and the heat stay inside, and the engine is shielded from the weather or industrial conditions outside. Whether it is very cold or very hot out, we manage the conditions inside to be the best ones for making pure water and inexpensive dry air. That is why the machine keeps making its rated amount of pure water or inexpensive dry air under a wide range of conditions. To see how the technologies compare, see the AWG Technology Platforms Comparison.

How does the WaHa Vaporator® make pure water and inexpensive dry air?

The WaHa Vaporator® makes pure water and inexpensive dry air in three steps, over and over. Our sealed regeneration engine is responsible for the last two: release and collect.

  1. Catch. A fan pulls air across a wheel. The walls of the wheel hold a drying material that grabs the water vapor, the way a sponge soaks up water. The air that comes out the other side is dry. That is the inexpensive dry air many customers want.
  2. Release. Our sealed regeneration engine uses a heat pump to warm the wheel, and the drying material lets go of the vapor.
  3. Collect. The same engine uses the same heat pump to cool a surface, and the vapor turns into drops of pure water that you collect.

Because the engine is sealed, it keeps its water and heat inside and is shielded from the weather or industrial conditions outside. It works efficiently under a wide range of conditions, day and night, not just when the sun is out. For every step, with pictures, see the page on how it works.

How does the WaHa Vaporator® work, step by step?

We have a whole page on this, with pictures and every step. Please read it here: How It Works (https://www.wahainc.com/the-waha-vaporator-engine/).

Is the WaHa Vaporator® only for making water?

The WaHa Vaporator® makes two things. It uses two inputs, humid air and energy, to create both pure water and inexpensive dry air. Some customers want the pure water; others want the inexpensive dry air. It's the same engine either way. It's just how we measure the output. Are we measuring it on delivering water reliably, or are we measuring the output humidity from the machine?

Why is the dry air from the WaHa Vaporator® inexpensive?

To dry air, the machine does two jobs. First, a desiccant, a material that pulls water out of the air, catches the water vapor. Then the machine has to push that water back out of the desiccant so it can catch more. Pushing the water out is called regeneration, and it takes heat. Making that heat is the biggest energy cost of drying air. Five things let us do it with much less energy.

  • A heat pump, not a heater. Older systems make the heat with an electric heater or a gas burner. Those get one unit of heat, at most, from each unit of energy they use. A heat pump moves heat instead of making it, so it delivers more heat than the electricity it uses. That ratio is called the coefficient of performance, or CoP. A heater has a CoP of 1. Heat pumps deliver from about 2.5 up to 7.5 units of heat for each unit of energy, so heater-based systems cannot match them.
  • A sealed engine that condenses water at a higher temperature. A heat pump uses less energy when the gap between its cold side and its hot side is smaller. That gap is called the temperature lift. Standard machines that cool air to collect water must set their cold side, the evaporator, at 5 to 15°C (41 to 59°F). In our sealed engine, water condenses at much higher temperatures, and because the engine is sealed, we can hold that temperature. So we set our evaporator much higher. A smaller lift means the heat pump uses less energy, so the CoP gets better again.
  • Heat that comes back. When water vapor condenses into drops, it gives off heat (called latent heat). In a standard machine, that heat is lost. Our engine is sealed, so we capture it and return it to the desiccant, where it helps push the water out. That means we need to make less heat.
  • A desiccant that lets go of water easily. Our desiccant is a MOF. It does not hold on to water as tightly as silica gel or zeolite do, so it takes less heat to push the water out.
  • A desiccant that works with low heat. A MOF can be regenerated at a low temperature, far below 100°C (212°F), the boiling point of water. Low-temperature heat takes less energy to make.

Together, these five things let the WaHa Vaporator® use 70 to 90% less energy than a silica gel wheel dehumidifier, the conventional design. That is why the dry air is inexpensive.

How is the WaHa Vaporator® different from other desiccant dehumidifiers?

A conventional desiccant dehumidifier dries the air, then heats the desiccant with either resistive heating or natural gas to release the water. The damp air is then exhausted outside through a duct.

Resistive heating and natural gas cannot match the coefficient of performance (CoP) of a heat pump. A heat pump moves heat instead of making it, so it delivers more heat than the electricity it uses. The WaHa Vaporator® uses a heat pump.

The WaHa Vaporator® also needs no exhaust, and it has none. It turns the humidity into liquid water, and you decide whether to use that water or not.

What happens to the water when the WaHa Vaporator® is drying my air?

The water comes out as pure liquid water. What you do with it is up to you. You can let it go down a drain. Many customers find uses for it once they think about it, and you can change your mind at any time.

Why does the WaHa Vaporator® use energy to catch, release, and collect the water?

Making water from air takes three steps: catch the water, release it from the MOF, and turn the vapor back into drops. Each step can be passive (nature does it) or active (the machine does it with energy). Our machine is active at all three. A fan pushes air across the MOF to catch the water. That also leaves the air dry, which is the inexpensive dry air many customers want. A heat pump heats the MOF so it releases the water, and the same heat pump cools a surface so the vapor turns into drops. Because the machine does the work itself, it makes water at any hour and in any weather, not just when the sun is out. It also reuses the heat that comes off when the vapor turns into drops (see "What is latent heat recovery, and why does it matter?"). The cost is that the machine needs steady power (see "Does the machine need to run all the time?").

What is the difference between a passive machine and an active machine?

A passive machine uses no energy except what nature gives it: cool nights and sunshine. Here is why night matters. Cool air is closer to being full of water, which is why you find dew on grass or on a car window in the morning. Some passive machines collect that dew overnight, the way drops form on a glass of ice water, except the night air does the cooling. Others soak the water into a drying material overnight, and the next day the sun's heat releases it as water you can collect. Either way, a passive machine makes one small batch a day at most, and a cloudy day or the wrong season makes even less.

An active machine uses energy to do the work, so it can make water all day and all night, in any weather, and that adds up to a lot more water. That energy can come from the power grid (the electric lines that run to homes and businesses), from renewable sources like solar panels or wind turbines with batteries, or from waste heat (heat that a factory or power plant would otherwise throw away). So an active machine can run away from the grid, but it needs steady power (see "Does the machine need to run all the time?"). The WaHa Vaporator® is an active machine that makes pure water and inexpensive dry air. To see what "active" can mean, see "What are the different kinds of active machines?"

What are the different kinds of active machines?

A machine that makes water from air does two jobs. It releases the water from its drying material, which is called desorption. Then it turns that water vapor back into drops, which is called condensation. "Active" can mean different things, depending on which jobs the machine controls.

  • Active desorption. The machine uses energy, usually heat, to release the water from the drying material, instead of waiting for the sun.
  • Active desorption with passive condensation. The machine releases the water with energy, but the vapor turns into drops at the temperature and pressure of the outside air. The weather decides how well that works, so there are limits.
  • Active desorption and active condensation. The machine uses energy for both jobs, so the vapor turns into drops under controlled temperatures and pressures.

The WaHa Vaporator® is an active system with active desorption and active condensation.

How long has WaHa been working on this?

The science started in the 1990s, and WaHa was founded in 2018. In 1995, Professor Omar Yaghi, then at UC Berkeley, made the first MOFs, a new kind of material with tiny holes that can hold on to certain molecules. By 2014, his team was studying how MOFs capture water from dry air. In 2017, a MOF harvester made water from the air in the Arizona desert, using only sunlight and cool nights. Those early tests used machines that run on sun and cool nights only, and they proved the idea worked before WaHa existed. WaHa was co-founded in 2018 to turn this science into machines that make water all day and all night. A WaHa countertop prototype was shown at the Smithsonian's FUTURES exhibition in Washington, D.C., in 2021 and 2022. Our first field pilots began in West Texas in 2023.

What does the Nobel Prize have to do with WaHa?

Professor Omar Yaghi, who shared the 2025 Nobel Prize in Chemistry for his work on MOFs, is one of WaHa's original co-founders and a shareholder. Two other scientists, Susumu Kitagawa and Richard Robson, shared the prize with him. The prize honored MOFs as a whole, not our machine, and the WaHa Vaporator® uses a MOF. WaHa also holds an exclusive license from UC Berkeley to three water-harvesting MOF patents from Professor Yaghi's laboratory; see the Patents page.

Why make water where people live

Why make water where people live instead of piping it, trucking it, or turning seawater into drinking water?

Every other way of getting water to people has a catch. Pipes take years to build. Trucks come only now and then. Seawater plants need to be near the sea and leave the water tasting salty. The WaHa Vaporator® makes water right where people live, from the air. It needs no pipe, no truck, and no sea.

Why not just build more water pipes?

Pipes take a long time to build, often many years. Picture a new neighborhood at the edge of a town. Before anyone there can turn on a tap, someone has to plan it, pay for it, and dig pipe from a water plant to every street. Families can wait years. Pipes can also be unsafe. Old pipes in some cities contain lead, a metal that is harmful to drink, as happened in Flint, Michigan. A WaHa Vaporator® needs no pipe and can make water reliably right where it is installed. It can be set up in a day.

Why not deliver water by truck?

A truck brings water only when it shows up. In some places it comes once every two weeks, so families measure every bucket and make it last. Trucks also have a cost for everyone else: they burn fuel, crowd the roads, and someone has to pay for every trip. A WaHa Vaporator® makes water every day in the place where it is used, so no truck has to drive there.

Why not turn seawater into drinking water?

Taking the salt out of seawater is called desalination. The plants only work near the sea, and the water still has to be sent on to people by pipe or truck. Even after the salt is removed, many people don't like the taste, so in the Gulf countries of the Middle East, many drink bottled water instead. The plants also leave behind a very salty waste water called brine. Most plants pump it back into the sea, where it can harm sea life near the pipe. A plant makes about one and a half times as much brine as drinking water. A few huge plants are also easy to break or attack, and if one stops, a whole city can run short of water. The WaHa Vaporator® needs no sea and makes no brine. It needs only air and energy.

Can atmospheric water replace a city's water supply?

No, and it does not need to. A city sends one kind of water to every tap, and most of it goes to showers, toilets, laundry, and lawns. Only a few percent is used for drinking, cooking, and other specialized purposes. That small share is where people worry about what is in their water: PFAS (the "forever chemicals"), tiny bits of plastic, metals like lead, and many other chemicals that are rarely tested for, so their effect on health is not well known. The WaHa Vaporator® is built for that small share, and "Doesn't water made from air pick up whatever is in the air?" explains how its water stays clean.

With a MOF, the water starts out pure, and minerals can be added back for drinking. Without them, it suits uses where minerals cause problems. A CPAP machine needs mineral-free water, batteries do too, a car rinsed with it dries without spots, and steam cooking needs it or minerals leave spots and scale.

The WaHa Vaporator® fits best when you are worried about:

  • what is in your water
  • how your water tastes
  • how long it will take to get water from the municipal service
  • whether your water supply is failing or old

We do not replace your city's water. We complement it, in three ways.

  • Speed. You do not wait for the city to lay pipe to your door. A WaHa Vaporator® can be making water in a day.
  • Resilience. If the city supply fails, runs short, or is shut off, you still have water. The machine does not depend on pipes, trucks, or the sea.
  • Quality. The water starts out pure, so it suits the uses where minerals cause trouble. The uses described above all work better with pure water.
Doesn't water made from air pick up whatever is in the air?

In most machines, yes. Most water-from-air machines cool the air until drops of water form. Whatever else is in that air, like dust, smoke, and chemicals, can end up in the drops, and the machine has to filter it out afterward. With a MOF, the WaHa Vaporator® works differently. Its drying material, a MOF, has tiny holes, called pores, that are thousands of times narrower than a human hair. They let water vapor in and leave almost everything else behind. MOFs are the kind of material that won the 2025 Nobel Prize in Chemistry for our co-founder, Professor Omar Yaghi, and two other scientists. The water is then released and turned into drops inside a sealed chamber, away from the outside air. So with a MOF, the water is very clean to start with.

Why is all tap water cleaned to drinking standard when so little of it is drunk?

Because a city has one pipe to each home, and every tap on that pipe has to be safe to drink. A second set of pipes, for water that is not meant for drinking, would cost a great deal to build, so only a few places have done it. Most people pay to clean a whole bathtub of water to drinking standard, and then drink only a cup of it. The WaHa Vaporator® turns that around. It makes the small amount of water that needs to be pure, right where it is used.

The technology: MOFs, desiccants, and heat

What is a metal-organic framework (MOF)?

A MOF (metal-organic framework) is a powder full of countless tiny holes, too small to see. Picture a very small building set. Metal pieces snap together with rods to make a frame, and the empty spaces in the frame are the holes. There are so many holes that a spoonful of the powder has as much surface inside as a football field. Each kind of MOF is built so its holes catch one thing. The kind we use catches water vapor from the air, even very dry air, and lets it go again with gentle heat. Professor Omar Yaghi made the first MOFs in 1995 at UC Berkeley.

Why do you call a MOF a separator, not a filter?

A filter works like a strainer: it holds back things that are too big to get through. A MOF works differently. It is a nano separator; "nano" means extremely small. Its tiny holes are shaped and built so that they pick out one kind of molecule from a mix and hold on to it. In the WaHa Vaporator®, that molecule is water. The other things in the air mostly pass by. That is why we call a MOF a separator, not a filter.

How does a MOF favor water over other molecules?

Two things work together. The first is size. The holes in a MOF are far too small for big molecules, such as many smoke and chemical vapors, so they cannot get in. The second is grip. A few small molecules in the air can fit in the holes, but the MOF holds on to water more tightly than they do, so water takes their place. When the MOF is gently heated, what comes out is almost entirely water. That water is turned into drops in a sealed chamber, away from the outside air. That is why the water is very clean to start with. Silica gel does not work this way.

What is the MOF made of?

The MOFs we use today are built from aluminum, a common metal, and common carbon-based building blocks, like the metal pieces and rods in the building set described in "What is a metal-organic framework (MOF)?". They are put together in water, and the main leftover is salt water. The finished material has nothing caustic in it. At the end of its life, it can be dissolved back into the building blocks it started from, and those can be used to make new MOF.

What is a solid desiccant, and how is it different from a liquid one?

A desiccant is anything that pulls water vapor out of the air. A liquid desiccant is a strong salt solution that is sprayed into the air to soak up the water. A solid desiccant is a dry material that stays in place while the air flows past it, like the little packets in a pill bottle. The WaHa Vaporator® uses a solid desiccant, held in the walls of a slowly turning wheel, so there is nothing to spray.

How can a desiccant capture water from very dry air?

Even dry air has water in it. On a hot desert afternoon, 40°C (104°F), the air feels bone dry. Yet every kilogram (2.2 pounds) of it still holds about 7 grams (0.25 ounce) of water vapor, about the weight of seven paper clips. A solid desiccant is a drying material that grabs that vapor, like the little packets in a pill bottle or a new pair of shoes. The two most common ones, silica gel and zeolite, can both still grab water from dry air, but each has a catch. Silica gel, the kind in those packets, grabs only a tiny bit when the air is dry. Zeolite grabs more, but it holds on so tightly that it takes a lot of heat, and so a lot of energy, to make it let go. A MOF is built to grab a lot of water even from dry air and to let go with gentle heat. That is why the WaHa Vaporator® keeps working in places where other machines stop.

Why does it matter how tightly a desiccant holds on to water?

Think of a desiccant as a hand gripping water. A tight grip can catch water even where there is very little, but it takes more effort to open the hand again. A loose grip needs more water around before it can hold on, but it lets go easily. Scientists call a tight grip "water-loving" (hydrophilic) and a loose grip "water-shy" (hydrophobic). For a machine, "effort" means heat, and heat means energy. So every desiccant is a trade: pulling water from drier air costs more energy to release it. Zeolite grips very tightly, which is why it takes so much heat to let go. A MOF lets go more easily than silica gel or zeolite, and MOFs can be built with a stronger or weaker grip to suit the place where the machine will work.

How does a MOF pick up water, and why does temperature matter?

A MOF does not pick up water gradually. Each MOF has a "step," and it works like a door. Below a certain humidity, the door is shut, and the MOF takes up almost no water. At that humidity and above, the door is wide open, and the MOF takes up all the water it can hold. The MOFs we use have steps between 7% and 24% relative humidity.

Temperature changes what that step means. Warm air holds much more water than cold air at the same relative humidity, so a MOF with a 7% step finds about 4.5 grams of water per kilogram (2.2 lb) of air at 45°C (113°F), but only about a tenth of a gram at -10°C (14°F). So how much water there is to pick up depends on two things: the MOF's step and the temperature of the air. A MOF with a lower step works in drier air, but it holds on to water more tightly and takes more energy to release.

What is latent heat?

Latent heat is heat that water carries with it when it changes between liquid and vapor. When you sweat, the sweat turns into vapor and takes heat from your skin, which is why you feel cooler. The reverse also happens: when water vapor turns back into drops, it gives that heat back. That is why steam burns your skin worse than boiling water at the same temperature. As the steam turns into drops on your skin, it dumps a lot of heat. The word "latent" means "hidden," because this heat does not change the temperature you can measure. Boiling water stays at 100°C (212°F) no matter how long you keep heating it, until it turns into steam. The extra heat goes into the steam, hidden, and comes back out when the steam turns into drops.

What is latent heat recovery, and why does it matter?

Latent heat recovery means the machine reuses the heat that water vapor gives off when it turns into drops, so it needs less energy to make water. In the WaHa Vaporator®, the vapor turns into drops when we collect the water. A heat pump, the same kind of device that moves heat out of your refrigerator, picks up that heat and moves it to the drying material, where it helps the material let go of its water for the next batch. Without this, the machine would have to make all of that heat from new energy, and the heat from the drops would go to waste.

Does the WaHa Vaporator® depend on one specific material?

No. The machine is built around its engine, not around one material. The drying material can be swapped for another solid desiccant, as long as it lets go of its water with gentle heat. Gentle heat is about as hot as a cup of coffee that has sat for a few minutes, well below the boiling point of water (100°C, or 212°F). Our machines use a MOF today, and the engine can also run on silica gel, the old standard, the same material as the little packets in a pill bottle, used for decades. Each fits different places. A MOF works best where the air is dry, and it works as a separator, so almost only water gets in. Silica gel works best where the air is more humid, but it does not separate water from the rest of the air, so whatever is in the air can end up in the water, and the water has to be filtered. We use silica gel only for water that people will not drink. We choose the one that fits each site, and we are not tied to one supplier.

How do you choose the right desiccant for my climate?

We match the desiccant to the climate, with two goals. First, the machine must keep our promise at your site: at least 90% of the rated amount of water on at least 9 days out of 10 (see "What does the WaHa Vaporator® promise to deliver?"). Second, among the materials that can keep that promise, we pick the one that uses the least energy.

Here is why energy depends on the material. Some desiccants pick up water even when the air is very dry. They are water-loving, which scientists call hydrophilic. They hold on to water tightly, so it takes more energy to make them let go. Other desiccants pick up water only when the air is more humid. They are water-shy, which scientists call hydrophobic. They hold on to water loosely, so they let go with less energy (see "Why does it matter how tightly a desiccant holds on to water?"). The best desiccant for you is only as water-loving as your air requires.

  • Drinking water, and any place that is not very humid: a MOF. A MOF catches water even from dry air and lets go of it with gentle heat (see "How can a desiccant capture water from very dry air?"). It also works as a separator, so almost only water gets in (see "Why do you call a MOF a separator, not a filter?").
  • Very humid places: silica gel is possible. Where the relative humidity stays at 65% or higher, silica gel can work, and it can use less energy there. But silica gel is not a separator, so whatever is in the air can end up in the water, and the machine needs a filter. For that reason, we use silica gel only for water that people will not drink.

Either way, the engine is the same (see "Does the WaHa Vaporator® depend on one specific material?").

How long does the desiccant last?

In lab tests, a water-harvesting MOF caught and released water more than 250,000 times with no loss in performance. Every 5,000 rounds, we weighed the MOF full of water and again when dry. Across all 250,000 rounds, it never lost weight and never lost any ability to hold water. The test used plain room air with no filters, and it heated the MOF faster and harder than our machines do. Our wheel has eight sections, and each section takes a turn catching water and then letting it go, a turn that comes around every 8 to 32 minutes. A machine running day and night would reach 250,000 rounds in roughly 4 to 15 years. Production machines also have air filters, which need periodic maintenance.

Has a wheel been tested outdoors?

Yes. A desiccant wheel sat outside for a total of 20 months, first in West Texas, where there are dust storms, and then in the UAE, where there are sandstorms. It was never cleaned. These are two of the toughest places in the world to run a water-from-air machine. When we tested the wheel again, it held just as much water as before. Running day and night, that is roughly 27,000 to 110,000 rounds, about a tenth to nearly half of the lab test.

Can the wheel be cleaned?

Yes. If a wheel gets very dirty at a customer site, it can be cleaned with soap and water, using a process our engineers designed. The customer can do it, then put the wheel back in the machine.

What happens when a wheel needs to be replaced?

We ship out a new wheel. The customer puts the old wheel in the shipping container, puts the new one in the machine, and sends the old one back to us. We recycle it.

Is the WaHa Vaporator® patented?

Yes. WaHa holds the exclusive license to three water-harvesting MOF patent families from UC Berkeley (see "What does the Nobel Prize have to do with WaHa?"), and we hold patents on our own engine, including the sealed loop that recovers heat and reuses it. For the full list, see our Patents page.

Can I buy MOF from WaHa?

No. WaHa does not sell MOF. We buy it from chemical companies and build it into the desiccant wheel inside our machines. If you want one of our machines, see "How much does one of our machines cost?" If you need a replacement wheel, see "What happens when a wheel needs to be replaced?"

What else can MOFs be used for?

Scientists are developing MOFs for other jobs, such as capturing carbon dioxide, storing hydrogen and other gases, separating gases in industry, and cooling. WaHa uses MOFs for one job: making pure water and inexpensive dry air from the air around us.

Where it works and how well

Where does the WaHa Vaporator® work?

It works in almost every place where people live, including very dry places. What matters most is not how hot or cold it is, but how much water vapor is in the air. We promise at least 90% of the rated amount of water on at least 9 days out of 10. To see how a machine performs at your address, go to our Where It Works page. As a dehumidifier, the machine is rated by how dry the air is when it leaves (see "What does the WaHa Vaporator® promise to deliver?").

Why does the amount of water vapor matter more than the temperature?

Water vapor is the invisible water that is always in the air, even on a dry day. A machine that makes water from air can only collect what is there, so what counts is how much vapor the air holds, not how hot or cold it feels. A hot desert afternoon at 40°C (104°F) feels bone dry, with a relative humidity of about 15%. (Relative humidity compares the vapor in the air with the most the air could hold at that temperature.) Yet every kilogram (2.2 lb) of that air still holds about 7 grams (0.25 oz) of vapor, about the weight of seven paper clips. That is plenty for the WaHa Vaporator® to work with.

Why do you measure the water in air in grams per kilogram?

Relative humidity can mislead, because it changes with the temperature even when the amount of water in the air stays the same. Think of the air as a bucket that holds water vapor. Warm air is a big bucket, and cold air is a small bucket. Here is why. In warm air, the water molecules move fast and stay apart as vapor. In cold air, they slow down, stick together, and turn into drops. That is why a cold glass of water gets wet on the outside: the air touching the glass cools, and some of its vapor turns into drops. A small bucket cannot hold as much.

Relative humidity tells you how full the bucket is. When the air cools, the bucket shrinks, so the same water fills more of it.

What matters to a water machine is not how full the bucket looks, but how much water is in it. So we count the water itself. We weigh the water vapor in 1 kilogram (2.2 lb) of air and give the answer in grams per kilogram, written g/kg.

In the U.S., dehumidifier engineers count the same thing in grains per pound (gr/lb). A grain is a tiny unit of weight, and 7,000 grains make a pound. So 1 g/kg equals 7 gr/lb.

Here is how one day can look in two seasons.

  • A summer day in the desert. At 40°C (104°F) in the afternoon, the air feels bone dry, with a relative humidity of about 15%. Yet each kilogram of that air holds about 7 g (0.25 oz) of water vapor, about the weight of seven paper clips. By evening the air cools to 20°C (68°F). It still holds about 7 g/kg, but the bucket is smaller, so the relative humidity has climbed to about 48%.
  • A winter day. At -5°C (23°F) in the afternoon, the relative humidity might be 50%, and each kilogram of air holds only about 1.3 g of water vapor. By evening the air cools to -10°C (14°F). It still holds about 1.3 g/kg, but the bucket is smaller, so the relative humidity has climbed to about 73%.

Notice that the nearly empty desert bucket holds about five times as much water as the half-full winter bucket. Our machine works like a ladle. Each pass of air through the machine scoops out some of the water. Where the air holds a lot of water, one or two scoops go a long way. Where it holds little, the machine has to scoop many more times, which means moving more air to get the same amount of water.

The WaHa Vaporator® keeps making its rated amount of water down to about 1 g/kg in cool air. Air colder than about -20°C (-4°F) holds less than that, even when it feels damp.

How dry can the air get before the WaHa Vaporator® makes less than its rated amount of water?

The air has to pass two tests.

  • Not too dry. The air needs a relative humidity of at least 10%. Think of the air as a bucket: it should be at least 10% full. Below that, the machine's MOF cannot catch enough water, so the machine goes to sleep until the air gets more humid (see the "too dry" FAQ).
  • Enough water in the air. The air needs at least about 1 gram of water vapor in every kilogram (2.2 lb) of air, written 1 g/kg. Cold air has a small bucket, so it holds little water even when it feels damp. Below about -20°C (-4°F), air holds less than 1 g/kg. The machine still makes water there, but less than its rated amount.

Which test matters depends on the temperature. At about 14°C (58°F), the two tests are the same: 10% relative humidity is 1 g/kg. In hotter air, the 10% test comes first. At 40°C (104°F), 10% relative humidity is about 4.6 g/kg. In colder air, the 1 g/kg test comes first.

To see how a machine will do at your address, go to our Where It Works page.

This page is about the WaHa Vaporator® as a water machine. When it works as a dehumidifier, we rate it by how dry the air is when it leaves the machine, at your airflow and your air temperature (see "What does the WaHa Vaporator® promise to deliver?").

What does the WaHa Vaporator® promise to deliver?

The WaHa Vaporator® makes pure water and very dry air from the same engine (see "Is the WaHa Vaporator® only for making water?"). We rate it differently depending on which one you buy it for.

As a water machine. The rating is the amount of water the machine is built to make each day. The Oasis-24, for example, is rated at 24 L (6.3 gal) a day. Our machine is designed to make that full amount every day, across the whole range of air it supports (see "How dry can the air get before the WaHa Vaporator® makes less than its rated amount of water?").

Be careful with any water-from-air rating, ours included. Many makers state their output for their best day only: warm, muggy air (see "Why do some water-from-air machines claim very high output?"). A rating that holds only on the best day is a best case, not a rating. On any other day, those machines make less water than the number on the box.

Most AWG companies do not publish what you need to check their rating, so for each AWG product you're considering, ask them these five questions:

  1. How dry can the air get, and the machine still make its full rated output? Give the temperature, the relative humidity, and the g/kg of the air at that point. (g/kg is the grams of water vapor per kilogram (2.2 lb) of air.) The condition where the machine is rated is not the answer.
  2. At what g/kg does the machine stop making water? Give the temperature, the relative humidity, and the g/kg of the air at that point.
  3. What is the coldest air temperature at which the machine still makes its full rated output? Give the temperature, the relative humidity, and the g/kg of the air at that point.
  4. What is the hottest air temperature at which the machine still makes its full rated output? Give the temperature, the relative humidity, and the g/kg of the air at that point.
  5. Who measured these numbers, and where: in a lab, or in the field? A test report is evidence. A number that nobody measured is a claim.

Do not accept the temperatures where the machine merely runs or makes a little water. Only the full-output numbers tell you whether the rating holds.

Then enter the answers into the vendor self-test on our Where It Works page. It grades that machine at your site by the same standard we use for ours, and it marks numbers as self-declared until a lab or field record backs them up. A maker that will not give you these numbers is asking you to take its rating on faith. For the full list of questions to ask, see "How should I compare water-from-air machines?"

Our rating is a minimum, not a best case. At your site, on at least 9 days out of 10, your machine will make at least 90% of its rated amount. For the Oasis-24, that is at least 21.6 L (5.7 gal). We count the days that fall outside the machine's range, such as very dry or very cold ones.

We hold ourselves to the standard of a water utility. When you turn on a kitchen faucet, water comes out. You do not think about it, and that is true every day, all year, for years. Water is the essence of life, so a machine that makes it should be just as dependable. We test our machines through every season (see "Has anyone independent tested the WaHa Vaporator®?") and design them to last for years (see "How long will the machine last?"). We commit to that kind of experience: we deliver the water we say we will.

We have also proposed this measure as an industry standard, so that customers can get an independent, objective measure of how reliable every machine is, ours or anyone else's. Our promise is a minimum, and it is only a beginning. A real faucet works every day, so over time the bar for every machine should be much higher. The standard is still a proposal. We published the draft at https://github.com/wahainc/awg-viability-standard for anyone to read and use, free, and we are working to get the industry to adopt it.

To see how a water machine will do at your address, go to our Where It Works page.

As a dehumidifier. The rating is how dry the air is when it leaves the machine, at your airflow and your air temperature. To compare dehumidifiers, see "How should I compare dehumidifiers?" To see what to expect at your site, use our dehumidification requirements form.

Can the WaHa Vaporator® make more water than its rating?

Yes, if you want it to. Most customers want exactly what they paid for, every day, and the machine can do that. You choose:

  • Make just the rated amount. The machine makes its rated amount each day, such as 24 L (6.3 gal) for the Oasis-24, and then stops.
  • Make extra. On days when the air holds plenty of water, the machine keeps going and makes more, until your storage tank is full.

In humid air, the extra water costs very little energy for each liter. In dry air, it costs more. When the air is too dry, the machine goes to sleep and uses almost no energy (see "What happens when the air is too dry?").

Be careful with a maker that brags about extra water. A machine can make a great deal of water on a hot, muggy day. Some makers add up a whole year of production and divide it out, then say the machine made 100% of its rating. The average hides the winter, when the same machine may make no water at all. A family needs water every day, and you cannot drink an average. That is why our promise counts days, not yearly totals (see "What does the WaHa Vaporator® promise to deliver?").

Ask about storage, too. If a machine makes 200% or 300% of its rating on a good day, where does the water go? Do you have a tank big enough to hold it? If not, the extra is wasted, and the savings are not real. A tank that holds a day or two of extra water cannot cover a dry winter. Our machine stops making extra water when your tank is full, so it never makes water you cannot store.

Does the WaHa Vaporator® make the same amount of water day and night?

Yes. The machine runs on steady power, not on sunlight, so it does not need the sun or a cool night to work.

What matters is how much water vapor is in the air, and that changes with the weather, not with the clock. In one day, the air cools after sunset and the relative humidity goes up, but the amount of water in each kilogram (2.2 lb) of air stays about the same unless the weather changes (see "Why do you measure the water in air in grams per kilogram?"). So the machine makes its rated amount of water day and night.

The energy the machine uses stays steady too (see "Does the energy the machine uses change with the weather?").

Does the energy the machine uses change with the weather?

A little, and we design it that way. We aim to keep the energy for each liter as flat as possible throughout the entire range of ambient conditions where we work, so you can plan on what your water will cost.

  • Hot, humid air. The machine is very efficient. The air holds a lot of water, so each pass of air collects plenty.
  • Drier or colder air. The machine works a little harder, mainly by running its fan faster to move more air across the MOF. When there is less humidity in the air, in order to generate our stated amount of water, we need to increase fan speed so the MOF is presented with the same amount of water vapor (see "Why do you measure the water in air in grams per kilogram?").

The result is a narrow range. The Oasis-24 uses 0.4 to 0.75 kWh for each liter, which is 10 to 18 kWh a day. A kWh, or kilowatt-hour, is the unit on your electric bill.

Larger machines use less energy for each liter. A larger compressor wastes less energy than the small one in a machine that makes 24 L (6.3 gal) a day or less, and it is more efficient. Some compressor designs work at large scale and are not available in very small sizes. Our target for production machines is 0.24 to 0.3 kWh for each liter. Our figures count every energy input, including fans, controls, and any heat we supply.

Machines that cool the air with a compressor, like a refrigerator, can swing widely. As the air gets drier, they use much more energy for each liter of water, and the amount of water they produce drops dramatically. So you pay twice: much more energy for much less water (see "Why do some water-from-air machines claim very high output?").

When the machine works as a dehumidifier, we state its energy for the whole machine except the fan that moves the air. Other dehumidifiers are rated that way, so you can compare fairly (see "How should I compare dehumidifiers?").

Can the WaHa Vaporator® work in freezing weather?

Yes. Cold does not stop the machine. What limits it is how much water the cold air holds. Cold air is a small bucket, so it holds little water vapor (see "Why do you measure the water in air in grams per kilogram?").

Even so, a winter day at -5°C (23°F) holds about 1.3 g of water vapor in each kilogram (2.2 lb) of air. That is enough for the machine to make its rated amount. Below about -20°C (-4°F), air holds less than 1 g/kg. There, the machine still makes water, but less than its rated amount (see "How dry can the air get before the WaHa Vaporator® makes less than its rated amount of water?").

Freezing is also a plumbing problem, because ice can block water lines. A cold-weather package keeps the water line and the pump heated.

One of our pilot machines has run in Sweden since 2024.

Can the WaHa Vaporator® work in very hot weather?

Yes. We tested the machine in a test chamber up to 55°C (131°F). The machine sits outdoors, so that is the temperature of the air around it. The machine can run hotter than that, but we judged 55°C was enough. The hottest temperature officially recorded on Earth is 56.7°C (134°F), in Death Valley in 1913, so the machine works in almost every place where people live.

Hot air is not a problem for the machine, because hot air still holds water. A desert afternoon at 40°C (104°F) feels bone dry, yet each kilogram (2.2 lb) of that air holds about 7 g of water vapor (see "Why does the amount of water vapor matter more than the temperature?").

Machines that cool the air with a compressor, like a refrigerator, stop working in heat above about 43°C (109°F). A compressor machine has to dump heat into the outside air, and in air that hot it cannot dump enough, so it shuts itself off to protect the compressor (see "Why do some water-from-air machines claim very high output?").

Will the WaHa Vaporator® work in a very dry place like Phoenix or Riyadh?

Yes. Phoenix and Riyadh are two of the driest big cities in the world, and the machine works in both. Two limits matter, and neither is a problem in these places.

  • Too cold. Cold air holds very little water vapor. Below about -20°C (-4°F), each kilogram (2.2 lb) of air holds less than 1 gram of vapor. The machine still makes water there, but less than its rated amount.
  • Too dry. At times of day, in places like the Atacama, Riyadh, and Phoenix, the air gets drier than 10% relative humidity. The machine puts itself to sleep, with only its computer and sensor on, so it uses almost no energy. When the air gets more humid, it wakes up and makes water again.

We checked four years of daily weather data. On 99.9% of days in Phoenix and 100% of days in Riyadh, the machine would make at least 90% of its rated amount. To check your own address, go to our Where It Works page.

What happens when the air is too dry?

In places like the Atacama, Riyadh, and Phoenix, there are times of day when the air gets drier than 10% relative humidity. It is usually not a whole day. A temperature and humidity sensor tells the machine when the air is too dry. When that happens, the machine puts itself to sleep and keeps checking the air around it. Only its computer and its sensor stay on, so it uses almost no energy. When the humidity rises again, the machine turns itself back on and starts making water.

Will the WaHa Vaporator® take all the water out of the air?

No. Picture an indoor football stadium with 60,000 people in it. They all breathe, but no one worries that they will use up all the oxygen, because the building holds a huge amount of air and that air keeps being replaced. Water in the air works the same way. The machine takes some of the water from the air that passes through it and sends the air back out. The air around it is vast, and wind and weather keep bringing in more.

A machine needs fresh air to work. If you install more than one, leave enough space between them for air to flow.

Can you test a machine at my site's conditions before I commit?

Yes, and we already have. In our environmental test chamber, we have tested the machine across nearly every combination of air temperature and humidity found on Earth, from cold, dry winters to hot, humid summers and hot, dry summers. To see how a machine performs at your location, enter it on our Where It Works page. Most of the results there rest on measurements, not just calculations. If you think your site is unusual, contact us. We will be happy to evaluate your conditions. If you need a dehumidifier, tell us your airflow, your air temperature and humidity, and how dry you need the air leaving the machine.

How should I compare water-from-air machines?

Ask every company, including us, the same five questions. Ask for the answers in writing.

Whenever a question is about the air, ask for three numbers: the temperature, the relative humidity, and the mixing ratio. Mixing ratio is the grams of water vapor in each kilogram (2.2 lb) of air, written g/kg (see "Why do you measure the water in air in grams per kilogram?"). The company should supply all three. Any two give the third, so you can check its answer.

  1. At what mixing ratio does the machine still make 90% of its rated output, and at what mixing ratio does it stop making any water? Ask for the temperature and relative humidity at each point too.
  2. What are the coldest and hottest air temperatures at which it still makes its full rated output? Ask for the relative humidity and mixing ratio at each one. Do not accept the temperatures where the machine merely runs.
  3. How much energy does it use for each liter, counting everything? Ask for the answer at the condition where the company rates the machine, at any other conditions it has tested, and at each of these four:
    • 30°C (86°F) and 80% relative humidity, about 22 g/kg
    • 25°C (77°F) and 60% relative humidity, about 12 g/kg
    • 20°C (68°F) and 55% relative humidity, about 8 g/kg
    • 15°C (59°F) and 20% relative humidity, about 2 g/kg

    Ask how much water the machine makes at each. If it makes none, the company should say so. That is its answer.
  4. What is the quality of the water at the machine's outlet, before any filter or treatment? Ask for results from an accredited laboratory, on water straight out of the machine, in these units:
    • Total dissolved solids (TDS): parts per million (ppm), the same as milligrams per liter.
    • Bacteria: colony-forming units per milliliter, and E. coli per 100 milliliters.
    • Metals, such as lead and arsenic: micrograms per liter (μg/L), listed metal by metal.
    • PFAS: nanograms per liter (ng/L), by EPA Method 533 or 537.1.
    • Microplastics: particles per liter, with the smallest particle size the test can detect.

    Ask which laboratory ran the tests.
  5. How was each of these numbers found? Modeled means the company calculated it. Measured means the company tested a machine itself. Verified means an independent third party, with no stake in the result, tested it. Ask the company to label every number, and ask to see the report for any number it calls measured or verified.

If a company cannot or will not answer, that tells you something about the company.

Our full checklist is on the AWG Technology Platforms Comparison page.

How should I compare dehumidifiers?

Ask every company, including us, the same two questions.

  1. How dry is the air when it leaves the machine, at my airflow and my air temperature?
  2. How much energy does it use to get there? Ask whether that number includes the fan that moves the air.

A dehumidifier is judged by the air it delivers, so these two numbers tell you what you are really buying. Ask for them on your site's hottest, muggiest day, not only on an average day. Our V1000 handles 1,000 cubic meters of air per hour (about 590 cfm). Tell us your airflow, your inlet temperature and humidity, and how dry you need the air on our dehumidification requirements form, and we will tell you what to expect.

Why do some water-from-air machines claim very high output?

Many companies state their output on their best day: warm, muggy air around 30°C (86°F) and 60 to 80% humidity. On any other day they make less water and use more energy for each liter.

Air always carries some invisible water vapor. We count it in grams of water per kilogram of air (g/kg). Machines that cool the air with a compressor, like a refrigerator, start making less water when the air holds about 15 g/kg. That is a muggy day of 25°C (77°F) and 75% humidity. They stop working around 8 g/kg. That is a pleasant day of 20°C (68°F) and about 55% humidity. They also stop in heat above about 43°C (109°F).

Enter any machine's stated operating range on the Where It Works page to see how it performs at your site. Our promise holds across the whole range we support (see "What does the WaHa Vaporator® promise to deliver?").

Water quality and drinking water

How pure is the water the WaHa Vaporator® makes?

Our goal is water that is only water. The water that comes out of the machine has almost nothing else in it. Its TDS (total dissolved solids, the minerals and other solids dissolved in the water) is just 2 to 5 ppm.

The pure water comes from how the machine works. A MOF lets water vapor in and leaves almost everything else behind. The water is then released and turned into drops inside a sealed chamber, away from the outside air (see "Why do you call a MOF a separator, not a filter?"). For now, machines also carry a carbon filter as a precaution, and our goal is to not need one.

Water this pure is valuable for many uses (see "Can atmospheric water replace a city's water supply?"). But it is too pure to drink as it comes out. For drinking, we add minerals back (see "Can I drink the water straight from the WaHa Vaporator®?").

We test our water at California-accredited laboratories that use US EPA methods. We will continue to test it at accredited laboratories against US EPA drinking water standards, including PFAS (the "forever chemicals"), and we plan to add microplastics. We will publish the results here.

Can I drink the water straight from the WaHa Vaporator®?

Not quite, and that is because it is so pure. The water that comes out of the machine has almost no minerals in it (see "How pure is the water the WaHa Vaporator® makes?"). Water this pure is valuable for many uses, but it tastes flat, and most people expect drinking water to have a little mineral content.

For drinking, we add minerals back. The WaHa Rivara™ water hub, the WaHa Dispenser, and the Oasis-24 Integrated all do this, so the water you drink is pure, balanced, and safe. The hub can also adjust the taste to suit you.

If you use the water for something other than drinking, such as a CPAP machine, a humidifier, or steam cooking, you do not need to add minerals. Pure water is what those uses want.

Today: For pilots, we can deliver a hub now if you need drinking water.

What certifications does the WaHa Vaporator® have?

We are certifying the WaHa Vaporator® to the marks a water machine needs: NSF, for the parts that touch drinking water; UL, for electrical safety; CE, for Europe; and RoHS, which limits hazardous substances in electronics. Each country also has its own marks, and we will get the ones your country requires. Today, each part of the machine is certified on its own. Certifying the whole machine is still ahead. Every production machine will be fully certified before we sell it, whatever its size. Pilot machines are not certified for use in homes (see "What is the difference between a pilot machine and a production machine?").

We also test our water at California-accredited laboratories that use US EPA methods. We have tested it many times, and for more chemicals than the standard drinking-water tests ask for. In Dubai, an accredited laboratory found that water from an Oasis-24 and from a WaHa Dispenser met the Gulf drinking water standard's chemistry limits (see "Does the water from the WaHa Vaporator® meet the Gulf drinking water standard?").

Can I use the water in a laboratory or for electrolysis?

The water starts out very pure, so it is a good starting point for laboratories and for electrolysis, which splits water into hydrogen and oxygen. These uses have strict purity grades, and our water will likely need a final treatment step to meet yours. Tell us the grade you need, and we will tell you what to expect.

Can the WaHa Vaporator® clean dirty or contaminated water?

No. It makes water from the air, and it does not take in water from a tank, river, or tap. If your problem is dirty water, you need a water treatment system. A WaHa machine can give you a separate source of pure water that does not depend on the dirty one (see "Can atmospheric water replace a city's water supply?" and "Doesn't water made from air pick up whatever is in the air?").

What goes into the WaHa Vaporator®, and what comes out?

In: air and energy. Out: pure water and inexpensive dry air. The machine makes no brine and uses no treatment chemicals and no membranes. For now, machines carry a carbon water filter as a precaution, and our goal is to not need one. Washing the wheel now and then does not count as waste.

Power, siting, and day-to-day use

Does the machine need to run all the time?

Yes. Inside the machine, the section where the water is released has to stay at the right temperature for the material to let go of its water efficiently. If the machine stops, that heat fades, and it takes energy to build it back up. So the WaHa Vaporator® works best running nonstop, which means it needs steady power. Solar panels or wind turbines can supply it, but they need batteries, or the power grid, so the power never stops.

Can the WaHa Vaporator® run on solar power?

Yes, with batteries, because the machine works best running day and night (see "Does the machine need to run all the time?"). To size a system, multiply the liters you need each day by the energy per liter (see "Does the energy the machine uses change with the weather?"). That tells you how much electricity the panels and batteries have to supply. A machine that makes 24 L (6.3 gal) a day, for example, needs roughly 10 to 18 kWh a day.

You can also choose when it runs. A daytime-only setup needs enough batteries to carry it through passing clouds. A night-only setup runs on batteries that the panels charged during the day, and the machine is more efficient in cooler air. Either way, it makes about half the water we specify, because it runs about 12 hours out of every 24. Starting and stopping once a day is fine. What to avoid is starting and stopping often, because each start wastes some energy. The machine also runs on the power grid or on a generator, and some systems can use waste heat (see "Can the WaHa Vaporator® run on waste heat?").

Can the WaHa Vaporator® run on waste heat?

Yes. We can deliver a machine that runs on waste heat, which is heat left over from an engine, a factory, or a power plant that would otherwise be thrown away. That machine does not need the compressor, which uses most of the energy in our standard machine, so the electricity it needs on top of the waste heat is very low. We report two numbers for it: the electricity the machine uses, and the cost of the waste heat it uses. Other companies report only the energy their machine uses, so we give you both and you can compare fairly (see "Does the energy the machine uses change with the weather?").

What does it take to install the WaHa Vaporator®?

The machine connects to power, hardwired or with a plug, depending on your region. You do not need WaHa to install it. A local technician can install and commission it using our installation guide. "Commission" means setting it up and testing that it works. If your technician needs help, WaHa is available by phone or video. Large commercial and industrial installations are handled separately, so contact us for those.

Does the WaHa Vaporator® have to sit on a flat surface?

Today, yes. The machine needs a flat, level surface. In the future we plan mobile versions for cars, RVs, and military vehicles, and later for boats and ships.

Can I put the WaHa Vaporator® on a roof?

Yes. The machine works on the ground or on a roof. It needs a flat surface and steady power (see "Does the machine need to run all the time?"). A roof has to be strong enough to hold the machine, and the weight is on each product page. If you install more than one machine, leave space between them.

Can I use the WaHa Vaporator® near the ocean, or where the air is dusty?

Near the ocean. Salty air can corrode (eat away) many metals. Our test machine in Abu Dhabi sat outdoors at Khalifa University's Sas Al Nakhl campus, 1.5 km (0.9 mi) from the coast. It ran there for 15 months, and the stainless steel (316) did not corrode. We plan to offer a version with an IP65 shell made of 316 stainless steel. IP65 means dust cannot get in, and water sprayed from a hose cannot get in.

Coastal air is usually humid. The machine makes water there, and also in very dry air. To see what to expect at your address, use the Where It Works page.

In dusty air. Dust clogs the air filter, so you change it more often. How often depends on how dusty the air is. In Abu Dhabi and West Texas, the filter was changed every month. In many other places, 2 or 3 months between changes is common, and sometimes longer. Air filters can be paper filters that you replace, or washable filters.

Can I move the WaHa Vaporator® to a different place?

Yes. If you move it somewhere with a very different climate, such as from a humid place to a dry one, contact us. The wheel may need to be replaced with one matched to the new climate (see "How do you choose the right desiccant for my climate?").

Does the WaHa Vaporator® need an internet connection?

Every machine has the connection hardware built in, but you do not need to turn it on. If you subscribe to a service, it works best with the machine connected. You can watch how your machine is running on the web or in an app.

What maintenance does the WaHa Vaporator® need?

A few parts need regular care.

  • Air filters. They need periodic maintenance. How often depends on how dusty the air is. Air filters can be paper filters that you replace, or washable filters.
  • Water filter. Early machines carry a carbon filter as a precaution. Our goal is to not need one.
  • Mineral cartridges. If the water is being used for drinking water, these add minerals back to the water in very small, measured doses, like the ink cartridge in a printer. You replace them from time to time.
  • UV light. If the water is for drinking, the machine uses a UV light, which needs replacing about once a year.
  • Wheel. If it gets very dirty, you can wash it with soap and water.
How often does the UV light need to be replaced?

About once a year. The UV light wears out like any light bulb. Ours is rated for about 9,000 hours of use, which is a little more than a year if it runs every hour of every day. It is a small, low-cost part. If you have a subscription, WaHa replaces it for you. If you bought the machine, you replace it.

Who repairs the WaHa Vaporator®?

It depends on how you bought it.

  • Subscription. A WaHa technician comes to your site.
  • You own the machine. A qualified HVAC or refrigeration technician can handle the standard parts. WaHa supports the parts that are specific to our machine, such as the wheel. You can also swap the wheel yourself.
  • Distributors and OEM partners. They offer their own service plans.
How loud is the WaHa Vaporator®?

Our early pilot machines (see "What is the difference between a pilot machine and a production machine?") measured 60 to 63 dBA at 1 m (3.3 ft), about an arm's length away. A dBA is a unit of loudness; a bigger number means louder. That is about as loud as two people talking in normal voices. We measured at close to nominal conditions: 20°C (68°F) and 50 to 60% relative humidity, which is a typical indoor temperature.

This is a pilot measurement. Our indoor machines will need to be quieter, and we are working on that. We will publish the sound level of the production machines once they are measured.

What safety and monitoring features does the machine have?

If something goes outside its safe range, the machine stops itself safely. If the machine is connected, it sends you an alert (see "Does the WaHa Vaporator® need an internet connection?"). You can watch how it is running on the web or in an app. The dispenser tells the machine when the tank is full, so the machine stops making water until you need more (see "Why do I need a WaHa Dispenser? Why can't I use my own?"). The Oasis-24 Integrated also has a screen that shows how full the tank is (see "Can I see how much water is in the tank?").

If you turn on remote monitoring and subscribe to a service, WaHa watches the health of your machine. We update its software (firmware) when needed. If the machine starts to run outside its safe range, we send a technician.

Can I see how much water is in the tank?
  • Oasis-24 Integrated: Yes. The screen shows how full the tank is.
  • Oasis-24 Outdoor: The machine itself holds only a very small amount of water. It is not built to store water. It collects a little and then pumps it out to a storage tank. If you use a WaHa Dispenser, you will be able to see how full its tank is in the app.
Is the WaHa Vaporator® safe to use in my home?

Yes, once it is fully certified. Certification means an independent lab has tested a machine against recognized safety standards. Production machines will be fully certified before we sell them (see "What certifications does the WaHa Vaporator® have?"). Pilot machines are not certified for use in homes (see "What is the difference between a pilot machine and a production machine?").

Can I connect the WaHa Vaporator® to my smart home or smart building system?

Yes. We will make an API available on the machine itself, even on the Oasis-24 Outdoor. An API is a way for other software to talk to the machine. For example, your smart home or smart building system will be able to read how much water the machine has made or how full the tank is. The WaHa Rivara™ water hub is designed to be the connection point between your WaHa products and smart home and smart building systems.

You will also be able to see, track, and download your own data, such as how much water your machine makes each day.

Today: Pilot machines have a dashboard that shows how the machine is performing. We have not opened the API yet.

Why do I need a WaHa Dispenser? Why can't I use my own?

Ordinary dispensers expect to be connected to a pressurized city water supply. Ours connects to the WaHa Vaporator®. It does four jobs that an ordinary dispenser does not. It tells the machine when the tank is full, so the machine stops making water until you need more. It uses UV light to keep the water pure while it is stored. It adds minerals back to the water for health and taste. And it connects to the machine's water supply, not to city pressure.

If you want to use your own dispenser, or any device that dispenses water, such as the water dispenser in your refrigerator door, buy the WaHa Rivara™ water hub. It does the same jobs for you, and then you can connect what you already own.

Can I connect the WaHa Vaporator® to my plumbing or to a storage tank?

Yes. The machine can connect to:

  • a WaHa Dispenser, which includes a storage tank;
  • a storage tank you already own, using a WaHa Rivara™ water hub;
  • for larger machines, a large-scale WaHa Rivara™ water hub that stores and mineralizes the water.

We have not set limits such as water pressure or tank size yet, so contact us about your plumbing.

Can I connect more than one dispenser?

It depends on the machine. The Oasis-24 Integrated has one dispenser built in. The Oasis-24 Outdoor connects directly to one WaHa Dispenser. To connect more, buy a WaHa Rivara™ water hub, then connect your own dispenser or any device that dispenses water, such as the water dispenser in your refrigerator door. How many dispensers a hub supports depends on the size of the hub.

For larger machines (200 L (53 gal) a day and up), a large-scale WaHa Rivara™ water hub stores and mineralizes the water. You can then connect as many off-the-shelf dispensers as you need.

Sizes, lifespan, and design

What sizes does the WaHa Vaporator® come in?

When the machine is making pure water. We name each size by the liters of water it makes in a day: Oasis-5, Oasis-24, Oasis-200, Oasis-500, and Oasis-1000. Our first machines, the Oasis-24 Integrated and the Oasis-24 Outdoor, are expected to deliver in September 2027. The Integrated may come in an indoor version and an outdoor version, and the outdoor version will have an IP65 shell, which keeps out dust and hose spray. Larger sizes come later. Our goal for the largest systems is 20,000 L (5,300 gal) a day in one 12 m (40 ft) shipping container. To choose a size, see "Which size do I need?" The right size depends on how much water you need each day and where the machine will be located.

When a machine is making inexpensive dry air. We name each size by the air it moves, in cubic meters an hour. The V1000 moves 1,000 cubic meters (about 590 cfm) an hour, and it is largely the same machine as the Oasis-24 Outdoor. We have not set larger sizes yet. The right size depends on your airflow, the temperature and humidity of the air going in, and how dry you need the air coming out. We will publish a requirements form on our website so you can tell us.

The promise is different for each. For water, we promise liters a day. For dry air, we promise how dry the air is when it leaves the machine.

How large can the WaHa Vaporator® get?

Very large systems are not one big machine. They are made of smaller machines working together. Our goal is 20,000 L (5,300 gal) a day in one 12 m (40 ft) shipping container. If one machine needs service, the others keep running. You can start small and add machines, or containers, later. A container does not have to be full. The machines also fit in tighter places, such as a rooftop, a narrow deck, or a mechanical room.

Which size do I need?

Start with how much water you need each day. Then enter your address on our Where It Works page to see how much water a machine makes there.

Here is how much water people need, according to the World Health Organization (WHO) and the United Nations:

  • Drinking and food: about 2.5 to 3 L (0.7 to 0.8 gal) per person per day.
  • Health and hygiene: at least 20 L (5.3 gal) per person per day.
  • Most basic needs: 50 to 100 L (13 to 26 gal) per person per day.

The Oasis-24 makes 24 L (6.3 gal) a day, and we promise at least 21.6 L (5.7 gal) on at least 9 days out of 10 (see "What does the WaHa Vaporator® promise to deliver?"). That covers drinking and food for seven or eight people. For more water than that, you need a larger system or several machines (see "How large can the WaHa Vaporator® get?"). For the size of the Oasis-24 Integrated's tank, see its product page.

When will larger machines be available?

We expect to deliver our first machines, the Oasis-24 Integrated and the Oasis-24 Outdoor, in September 2027. Larger machines come after those. We will announce dates as they are set.

If you need a larger system, tell us your site and how much water you need each day. Large-scale systems (1,000 L (264 gal) a day and above) are built by combining several smaller systems running in parallel (see "How large can the WaHa Vaporator® get?"). Prices depend on the site, so please contact us.

Why are all your pilot machines the same size?

There are two reasons. First, a small machine proves our claims at a much lower cost than a large one. Second, we are a young company, so we decided that every pilot will be a 24 L (6.3 gal) a day machine, or a V1000 dehumidifier. The engine is the same at every size. Above a certain size, larger machines use bigger parts, or several larger machines working together. We have also run a 200 L (53 gal) a day machine at a desert site in the UAE.

How big and heavy is the WaHa Vaporator®?

It depends on the model. You can find the size and weight on each product page.

How long will the machine last?

We design the Oasis-5 and the Oasis-24 to last about 10 years, and our larger machines about 20 years. No production machine has run that long yet, so these are design goals, not field results.

Two parts wear out sooner, and both are easy to replace. The UV light needs replacing about once a year (see "How often does the UV light need to be replaced?"). The desiccant wheel is replaced about every 10 years on larger machines (see "What happens when a wheel needs to be replaced?"). The longest outdoor test of a wheel so far is 20 months in West Texas and the UAE, with no loss in performance (see "Has a wheel been tested outdoors?").

What matters most to you when you design the WaHa Vaporator®?

Four things matter most: reliability; steady production, whether that is pure water or inexpensive dry air; energy efficiency; and size and weight. Reliability comes first. A supply of pure water that people depend on, or a supply of inexpensive dry air that companies depend on, has to show up every day.

Has anyone independent tested the WaHa Vaporator®?

Yes. Universities have tested our machines, and more tests are under way.

  • Khalifa University, United Arab Emirates (independent): A 24 L (6.3 gal) a day machine ran outdoors for 15 months, from September 2024 to December 2025, through every season. It made 96% of its stated production.
  • Arizona State University (independent): ASU is testing a machine now. The test is early.
  • University of California, Davis (outside WaHa; the professor who ran the test advises WaHa): A machine ran as a dehumidifier in a vertical farm for 21 days. It lowered the humidity from about 80% to about 66%, inside the farm's target range of 60 to 75%.

Our full field record is on the Proven, Not Promised page.

Buying, pilots, and partners

Which markets will WaHa serve first?

We make two things: pure water and inexpensive dry air.

Pure water. We start where people already pay for bottled or delivered water: offices, hotels, commercial buildings, and homes. Here are two examples from very different markets. There are many, many others.

  • Home dialysis. More people are being treated for kidney failure at home. Engineers at dialysis companies told us some of these patients need up to 25 L (6.6 gal) of dialysis fluid a day. Imagine living in a small apartment in a big city. Where would you store that? We are working with dialysis companies on this. What they value most is that WaHa can reliably make water anywhere, at a consistent quality. If we do that, they can take care of the rest.
  • Workforce camps. These are places where workers live for mining, oil and gas, and other work in very dry regions.

Inexpensive dry air. This is useful in cold storage, clean dry rooms, and low dew point rooms (used for lithium-ion battery manufacturing and pharmaceuticals). It is also useful in coolers.

We are starting in the U.S., the Gulf, Mexico, and India.

What is the difference between a pilot machine and a production machine?

A pilot machine is an early machine we place at a customer's site to prove the technology there. A production machine is the version we sell.

  • Certification: Production machines will be fully certified before we sell them (see "What certifications does the WaHa Vaporator® have?"). Pilot machines are not certified for use in homes.
  • Shade: Pilot machines need a shade cover. Whether production machines will need one is not settled yet.
  • Delivery: Pilots are running today. We expect to deliver the first production machines in September 2027.

To learn about a pilot, see "How does a pilot work, and do you charge for it?"

How does a pilot work, and do you charge for it?

A pilot is a test of a WaHa machine at your site, and it runs for up to a year. Pilot sites cover both water and dehumidification. There is a pilot fee, and 100% of it is credited to your first order. You pay for shipping, duties, insurance, commissioning, and running costs. "Commission" means setting the machine up and testing that it works. WaHa pays for remote support, and we support your on-site engineer or HVAC technician. To ask about a pilot, contact sales@wahainc.com. You can also ask to visit our lab in Fremont, California, to see a machine running. We approve some visits, not all.

Can I get a WaHa Vaporator® in my country?

Yes. We have shipped pilot machines to the UAE, Saudi Arabia, Sweden, and Mexico, each entered as a commercial import. The customer is the importer of record, which means the customer's company clears the machine through customs and pays any duties. A local WaHa partner can help with the paperwork.

Can WaHa supply remote homes, schools, or humanitarian projects?

Yes, wherever there is steady power and a need for pure water. A remote home, a school, or a humanitarian project can run the machine on solar panels with batteries (see "Can the WaHa Vaporator® run on solar power?"). Contact us with your site and how many people you need to serve.

How do I become a finder, sales agent, distributor, or OEM partner?

There are four ways to work with us.

  • Finder or referral partner: introduces buyers to WaHa.
  • Sales agent: manages and completes the sale with customers.
  • Distributor: buys WaHa machines, sells them, and supports them in its own territory.
  • OEM partner: a company that builds the WaHa Vaporator® into its own products. OEM stands for original equipment manufacturer.

Any one of these can be our local WaHa partner. Partnerships usually start with one country and grow as the results come in. When someone in a partner's territory asks about a machine, we send them to that partner. If you are interested in becoming any of these, reach out to us at sales@wahainc.com.

What stage is WaHa in?

WaHa is early stage. We have pilot machines running in the field today, making water and drying air. We have not yet started selling production machines. Our first ones, the Oasis-24 Integrated and the Oasis-24 Outdoor, are expected to deliver in September 2027, and you can pre-order them now. The Outdoor is also our V1000 dehumidifier (see "What sizes does the WaHa Vaporator® come in?"), which is not yet open for pre-order. Our field record is published on the Proven, Not Promised page.

Do you offer a money-back guarantee?

Yes. If you are not happy with your WaHa Vaporator®, you can return it within 90 days of delivery and we will refund the full price of the machine.

If you pre-ordered, you can cancel any time before we start building your machine and get your deposit back in full.

What warranty comes with the WaHa Vaporator®?

Two years from delivery against defects in materials and workmanship. If we can't repair or replace a unit within 60 days of a valid claim, we refund the price of that unit. The warranty covers machines you buy. It does not cover wear parts: air filters, the UV light, and the mineralization cartridges used in a dispenser or the WaHa Rivara™ water hub.

Why does the Oasis-24 cost so much more than the water-from-air machines I can buy online for around $850?

Those machines cool the air with a compressor, like a refrigerator. They work well only where the air stays warm and muggy, and their makers usually state output for their best day (see "Why do some water-from-air machines claim very high output?"). That is about 7% of the world's land and only about 1% of water-stressed land, according to our Where It Works page. If you live in a place where those machines work well, buy one.

Everywhere else, you need a machine that keeps making water when the air is dry, cool, or very hot. The WaHa Vaporator® is built for that. We promise at least 90% of the rated amount on at least 9 days out of 10 (see "What does the WaHa Vaporator® promise to deliver?"). You can compare any machine's operating range with ours on the Where It Works page. A low price for a machine that either does not make water or does not make it reliably throughout the year is not a savings.

Can I pay for water instead of buying the machine?

Yes. Our primary way of selling the water we generate is through Water as a Service. WaHa installs the machine, owns it, and services it, and you pay for the water. We have not decided whether that will be a flat monthly fee, a charge for the water you use, or both. The terms depend on your site, so contact us for a quote.

Can I buy dehumidification as a service?

Yes. You do not have to buy the dehumidifier. You can buy the service instead. WaHa, or a partner, owns the machine and is responsible for both how well it performs and for maintaining it, and you pay for the dry air you need. The terms depend on your site, so contact us.

How much does it cost to make a liter of water?

The cost depends on the price of electricity where you are. The energy the machine uses for each liter is in "Does the energy the machine uses change with the weather?" Multiply that by your own electricity price to get your cost. We will cover energy cost in more detail soon.

How much fuel does a generator burn to make a liter of water?

We are not ready to release this number yet, but we will be soon.

How much does one of our machines cost?

Many customers do not want to own a machine. They want the pure water, or they want the inexpensive dry air, and they are used to paying for what they use. So we sell both as a service. For water, our primary way of selling is Water as a Service: WaHa installs the machine, owns it, and services it, and you pay for the water. For dry air, you can buy dehumidification as a service: WaHa, or a partner, owns the machine and maintains it, and you pay for the dry air you need. The terms depend on your site, so contact us for a quote (see "Can I pay for water instead of buying the machine?" and "Can I buy dehumidification as a service?").

If you would rather own a machine, the price depends on the model. Take the Oasis-24: the Outdoor is $5,000 and the Integrated is $6,500. Pre-order now and pay 40% less: $3,000 and $3,900. You pay 20% when you place your pre-order. You pay the rest, plus shipping and taxes, within 30 days of your final invoice, which we send before delivery. Our money-back guarantee covers it (see "Do you offer a money-back guarantee?"). Both machines are expected to deliver in September 2027.

The Oasis-24 Integrated includes everything needed to deliver water from the air: the machine, a storage tank, and a dispenser. The Oasis-24 Outdoor is the machine only. The WaHa Dispenser, which includes a storage tank, and the WaHa Rivara™ water hub are sold separately. Prices for our larger machines and the V1000 dehumidifier depend on the site, so please contact us. If you want to test a machine first, see "How does a pilot work, and do you charge for it?"

Have a question this page does not answer? Ask the WaHa team.

Contact WaHa